Pre Engineered Metal Building

A pre engineered metal building is the obvious choice for a church or other type of meeting place. You may have noticed these structures since they are quickly becoming the "standard" in constructions methods. When you are looking for a cost effective way to meet your building needs, you should certainly think about a steel building. A pre-engineered metal building takes the risk out of putting yourself and your organization into debt. It is easy to identify the advantages in a pre-engineered metal building.

You could delay development for years while you line up funding, but why? Some choose to rent space from other property owners in lieu of the responsibility of new construction. The problem with this situation is you only have access to your meeting place around someone else's schedule. After taking into account and dismissing these ideas, take some time to think about talking to a steel metal building manufacturer.

As property and construction capital become harder to obtain, new solutions become ever more imperative. A pre-engineered metal building may perhaps not be part of the dream you have held for your club, association or church, however that shouldn't stop you. Some of the greatest things come in unlikely packages and we sometimes miss out when we disregard them too quickly.

Overall Heat Transmission Coefficient (U-Value)

A unit used to express heat passage through a complete building section, including air films. U-Values serve as a basis for determining transmitted heat loss. The lower the U-Value, the higher the insulation value.

Recommended Installation Methods of Insulation

Roof insulation rolls are cut to lengths that will cover the distance from eave to eave, leaving a one-foot overhang on each side of the building.

1) Start at the end of the building and temporarily secure one end of the roll by attaching the insulation to the eave strut with double-faced tape.

2) Pull the insulation across the purlins with the vapor barrier toward the building interior. Double-faced tape attached to the opposite end of the insulation will keep tension on the roof roll while the metal panels are being attached over the insulation.

3) Install the next roll in the same manner, making sure the rolls are stretched tight, aligned properly and closely butted.

4) Fasten tabs using one of the methods described on the following page. Any rips or tears must be covered with matching facing tape to ensure a tight vapor seal.

5) Trim excess insulation flush to prevent it from acting as a wick and moving water into the building.

COMMERCIAL OFFICES

Your place of business should and can be more than just a place to work. It should reflect your company's image and be no less comfortable, functional or attractive than your living environment. Entry-ways and lighting, interior wall placement, and location of restrooms are as important in your office building as they are in your own home. Properly planned, your facility will serve your needs for many years to come, and you will avoid future changes or costly remodeling.

Modern ceiling and interior wall systems are very easily adapted to our manufactured building components using standard methods. For instance, perimeter sheet rock walls may be installed by simply attaching metal furring strips (hat channel) to the secondary wall framing members (girts). Similarly, acoustic panel or dry-wall ceilings may be installed by simply wrapping the ceiling suspension wires around the secondary roof framing members (purlins). Additionally, port-a-wall systems may be installed as needed throughout the structure.

Additional loads from heating and air conditioning systems, dropped ceilings, electrical conduit and lighting fixtures, or large mechanical sprinkler systems can be accommodated easily at your request with minimal cost, assuring a full roof-load certification.

The building components may represent a small percentage of the total cost of your office budget. Therefore, we are careful to ensure that the main structural components we provide will be reliable, helping to protect your investment against any water seepage, leaks or storm damage that can deteriorate your office complex.

When selecting the manufacturer of your building components, careful consideration must be given to both function and price. Your dealer will encourage you to have an architect review all aspects of your building plan, including lighting requirements, window heights, storage space, carpet wear ability, entrances, landscaping, parking and signage, to ensure you of a facility that will maintain its value and be a source of pride for years to come.

Steel Building Manufacturers

Finding a bona fide steel building manufacturer is sometimes difficult. Everywhere you look there seems to be someone selling a "factory clearance" or "cancelled order" buildings. Well 99% of it is a farce. There are too many brokers and re-sellers out there to count. What they want is your deposit. You can fight with them about the actual details later. They just want the deposit. Take advantage of all the resources available to you. Try locating the manufacturer to match your expectations. This may be slightly more time consuming, but well worth it when your new steel building is delivered exactly to your specifications.

Getting multiple bids for any kind of service is key. Ask several steel building manufacturers to quote your building and explain precisely by line item what your price includes. You can turn to the Internet to seek out steel building manufacturers, but be warned. You will encounter many wolves in sheep's clothing. Contact the Better Business Bureau, or other affiliations to ensure a company has a good track record. Form a list of qualified steel building manufacturers, do your research and you can gauge which manufacturers you prefer to deal with. Once your bids are returned to you, the selection process should be easy to complete. You can choose to follow up with the most qualified companies to purchase your metal building or to ask additional questions.