Base Condition

Every metal building has some type of base connection along the building perimeter, allowing the connection of sheeting. This "base condition" determines exactly how the panels connect to the foundation. To prevent water and pests from entering the building at the base, panels extend below the finished floor of the building. Online design and pricing systems allows users to choose from a number of different base options.

Standard Base Angle - Our system defaults to a standard base angle condition. This condition consists of a single angle member, attached to both the wall sheets and the slab. Please note that the standard base condition requires that the slab be formed with a 1½" sheet notch to allow the sheets to extend below the top of the slab.

Deluxe Trim - Deluxe base trim is another option for buildings with concrete slab foundations. Deluxe base trim combines base angle and trim into one piece, providing all the benefits of base trim and base angle. Deluxe base trim is only available in burnished slate color.

Base Girt - The base girt option is designed for buildings that sit on piers rather than a full slab. A base girt system does not rest on or attach to the foundation. The base girt attaches to clips on the columns about 6" above the foundation. The base girt provides a great connection for liner panel.

Base Channel - The Base channel is a "cee" shaped section that runs the perimeter of the building connected to the floor. It is most commonly used when a liner panel, or interior wall, is going to be installed. The "cee" section provides a pre-positioned connection point for inside panels. This approach requires a sheet notch in the slab (for an alternative, see the combination of base channel and base trim below).

Installation and Selection of Insulation

We provide the highest quality products available. However, proper installation and selection is imperative for maximum effectiveness. Please refer to installation instructions to ensure correct procedures are used. Facings that have been torn or punctured are no longer capable of blocking water vapor and may eventually do more harm than good. Be sure to quickly patch any holes in the vapor barrier.

When selecting a facing, special consideration should be given to its reflective quality. A facing with high reflectivity reduces the need for high light levels in work areas. This results in reduced energy costs and increased productivity.

Although the fiberglass insulation itself is not affected by cold weather, the facing is. Colder temperatures can cause cold crack, a situation where the facing becomes brittle and if handled can crack. Bay Insulation recommends that vinyl faced fiberglass products never be installed in temperatures below 40 degrees.

Trim and Gutter

The trim on a steel building serves two essential functions, to close transitions and protect the building from the weather. Trim also adds to the appearance of a building. Our sculptured trim gives the building a refined, quality appearance. Trim covers corner and edge areas of a building. For instance, eave trim creates a transition from the roof to the sidewalls and roof to endwalls.

Most metal building companies often supply "box" or generic trim pieces. This trim routinely has to be modified to fit, as it is created as multi-purpose - and does not fit well on standard panels. We fabricate each profile to match the design of your steel building. We do a lot of work in the shop that will save you headaches in the field. We hem all exposed edges of our trim so it installs easily, fits neatly, and looks great for the life of your building. Our trim is easy to install and adds to the look and the integrity of the building.

Overall Heat Transmission Coefficient (U-Value)

A unit used to express heat passage through a complete building section, including air films. U-Values serve as a basis for determining transmitted heat loss. The lower the U-Value, the higher the insulation value.

RECREATIONAL

Todays sports, conditioning and recreational centers represent a multi-billion dollar business which continues to grow each year. Attractive, ultra-modern facilities are springing up everywhere, offering a myriad of activities to meet the recreational demands of our society.

Immense clear span, low cost-per-square-foot, and low energy costs are vital to the successful construction and operation of recreational facilities. Whether your need is for a tennis, bowling or health club facility, computerized design and manufacturing help our design engineers create building systems that meet the precise demands of recreational facilities with an eye to architectural designs that fit into any surrounding. Our engineers have designed and manufactured buildings for sports courts, sports fields, game rooms, locker rooms, roller rinks, ice rinks, riding arenas, recreational centers and every other pastime you can imagine. The most important element in the design of all these facilities was combining practicality with efficiency, while providing for the customers' needs. Equestrian buildings provide excellent examples of how the flexibility of these custom designs allow for cost-effective solutions to those specific needs. Your dealer can value-engineer a dollar-saving building system that fits the bill, whether your needs include an arena, a barn or a complete riding facility. Available from one stall to one hundred, with a center row or in a shed-row design, our value-engineered horse barns give you maximum space with a functional layout designed to streamline your horse operations. Riding arenas are available fully-enclosed or as a roof-only structure. Clear span arenas are available up to 240 feet wide and in unlimited lengths. Our engineering department and your dealer can work with you to custom design a structure which maximizes your building site with attached barns, tack rooms, or hay storage areas.