Gutters & Downspouts

These are generally not required on steel buildings. However, use of these components often enhances the appearance of a building, control drip, splash and drainage.

Gutters and downspouts are an optional accessory that serves as trim. Gutters dramatically improve the appearance of buildings, and we recommend them for most building applications. Downspouts control the water falling from the roof, preventing the water from splashing up on the sides of the building.

On every Metal Building Depot building, die-formed ridge caps are used to cover the peak opening in the center ridge of the building. Some sellers provide a ridge roll cover that must be sealed with closures. Installing ridge roll trim is not an easy task. Over time the exposed foam closures deteriorate and there can be potential leak problems. Our die-formed ridge caps match the panel profile perfectly and are formed to fit the pitch of the roof. Die-formed ridge caps create an almost seamless transition across the roof.

RESIDENTIAL

Your decision to build is an important one. You have pictured yourself owning your own building, built just the way you want. You have imagined every detail, inside and out. It is a treasured vision, a promise you have made to yourself. And because your business operation is different from any other, your ideas about what you and your company want in a facility are unique. Your dealer, who is backed by a team of professional engineers, can help you turn your dream into a reality. Dealers have worked with a multitude of owners and developers to design efficient, economical structures that reflect the appropriate image for their operations. Architects and engineers will work with your dealer to design a building to meet your individual requirements. We can also work personally with you, your architect's plans, through your dealer to engineer a building system which uses practical, sensible, quality materials to achieve and complete your objective.

Using only the highest quality materials available, factory trained craftsmen use sophisticated Computer Aided Manufacturing (CAM) equipment to fabricate your building materials. Our commitment to excellence, attention to detail, and high quality workmanship assures you ease of construction, saving you money in time and labor. You have worked and planned to build a building that you can be proud of, and will serve your needs through the years to come; a place which is uniquely yours, a facility that is just as you imagined it. An establishment that brings your special ideas to life. It is an approach that lets you save money, yet build exactly the type of establishment you have always dreamed would be yours someday. This type of approach has pleased thousands of owners just like you. It is a concept that lets you use the pioneer spirit of people working together - you, your dealer, and Metal Building Depot, Inc. - to fulfill your own special vision of the American Dream . . . to build the building of your dreams today. Our steel frame load bearing wall systems with steel partitions provide attractive secure units. The use of fluted block, brick, wood, stucco, or steel can enhance the overall appearance to help attract even more customers.

Recommended Installation Methods of Insulation

Roof insulation rolls are cut to lengths that will cover the distance from eave to eave, leaving a one-foot overhang on each side of the building.

1) Start at the end of the building and temporarily secure one end of the roll by attaching the insulation to the eave strut with double-faced tape.

2) Pull the insulation across the purlins with the vapor barrier toward the building interior. Double-faced tape attached to the opposite end of the insulation will keep tension on the roof roll while the metal panels are being attached over the insulation.

3) Install the next roll in the same manner, making sure the rolls are stretched tight, aligned properly and closely butted.

4) Fasten tabs using one of the methods described on the following page. Any rips or tears must be covered with matching facing tape to ensure a tight vapor seal.

5) Trim excess insulation flush to prevent it from acting as a wick and moving water into the building.

Facings

In addition to acting as a decorative protection barrier, facings serve an integral part of the overall insulation system. Facings provide vapor barriers, light reflectivity and structural strength. In some cases, a reinforcement of fiberglass scrim is used for extra rigidity and greater impact resistance.

The effectiveness of a vapor barrier depends on three primary factors:

1) Location within the insulated section

2) Permeance

3) Proper installation

Condensation Control

The condensation process occurs when warmer moist air comes in contact with cold surfaces such as framing members, windows and other thermally conductive accessories, or the colder region within the insulation itself (if moisture has penetrated the vapor retarder). Warm air, having the ability to contain more moisture than cold air, loses that ability when it comes in contact with cooler surfaces or regions. When this happens, excessive moisture in the air is released in the form of condensation. If this moisture collects in the insulation, the insulating value is decreased.

In dealing with condensation, air may be considered to be a mixture of two gases-dry air and water vapor. One thousand cubic feet of air at 75°F can hold up to 1.4 pints of water. At 45°F, it can hold only 0.5 pints.

Relative Humidity is a percentage measurement of the amount of water vapor present in the air in relation to the amount it is capable of holding at that temperature. Therefore, 50% Relative Humidity would mean that the air is carrying only one-half of the total amount of moisture that it could be holding at that particular temperature. Cold outside air is usually much drier than warm inside air. Therefore, you can lower the Relative Humidity by bringing in outside air to mix with and dilute the moist inside air. At 100% Relative Humidity, the air is "saturated."

The temperature at which the air is saturated and can no longer hold additional moisture is called the dew point temperature. Whenever air temperature drops below its dew point, excess moisture will be released in the form of condensation. Condensation problems are most likely to occur in climates where temperatures frequently dip to 35°F or colder over an extended period of time.