Visible Condensation

To effectively control visible condensation, it is necessary to reduce the cold surface areas where condensation may occur. It is also important to minimize the air moisture content within a building through the use of properly designed ventilating systems.

Perm Rating

The perm rating, or permeance, is a measure of the amount of water that passes through one square foot of material per hour. The lower the perm rating, the more effective the barrier. A facing material with a perm rating of 0.1 or less is considered excellent. Anything with a rating above 1.0 is not considered a vapor barrier.

Ridge Vent

Ridge vents come completely assembled for ease of installation. Ridge vents supplied by Metal Building Depot are of a low profile design to provide gravity type ventilation. Because gravity ridge vents are designed to allow free airflow, some penetration of water during blowing rains is to be expected. Standard available finishes for the ridge vents are polar white and galvalume. Other colors may be available at an additional cost. Nominal ridge vent length is 10'-0". Ridge vents are available with 9" and 12" throats. Bird screens are provided as a standard. The ridge vents can be ordered as continuous or single units. Exterior parts are 26 gage painted or galvalume. Interior parts are all made of G90 galvanized steel. The substructure consists of 10 gage saddle straps with interior baffles of 24 gage steel. Lifter arms and damper slides are made of 18 gage steel. Manual operation is through activation of a pull bar which is attached internally to bell cranked type lifter arms connected to the damper with Teflon coated pins through the damper slides. Dampers are spring loaded to remain in the open position until the pull bar is operated and locked in the closed position. Dampers operate in a vertical manner. Each vent is opened by a pull chain that extends approximately 12" below the roof unless noted otherwise on the order documents. Other opening mechanisms are available at an additional cost upon special request. Ridge vents should not be placed closer than 5’-0" to the endwall steel line to allow room to properly flash the building. For example, a 90’-0" long building with ridge vents required the entire length should have no more than (8) units. The ridge vents are available with the following accessories:

Walk Doors

Walk doors can be provided as pre-assembled or knock down (field assembled). Metal Building Depot provides solid doors for both options in the following sizes: 3070, 4070, and 6070. The walk doors are typically keyed alike per project. Because of unknown variables, Metal Building Depot does not offer fire rated doors or doors to fit in masonry.

Features of the pre-assembled doors are as follows:

Foam insulated specifically designed for metal building use. Pre-assembled and self-framing for ease of installation. No framed opening required if Metal Building Depot standard girt spacing is utilized. Doors are finished in a two-coat primer; color selection is white or bronze. Doors are shipped in wood crates for protection. All doors have Grade 2 lever locks as standard. Hinges are ball bearing and powder coated. Insulated jambs. 3070 and 6070 doors are made of 20-gage material, 18 gage is available.

Features of the knock down doors are as follows:

Foam insulated specifically designed for metal building use. The walk door is shipped knocked down for field assembly. Doors are textured 20 gage galvanized prime painted and pre-finished in either white or bronze. Weather stripping and standard entrance lock is included. The walk door package is shipped with polybag and full cardboard carton. All doors have Grade 2 lever locks as standard. Hinges are ball bearing and powder coated.

Our Commitment to Quality

Our vision is to remain the industry leader through innovative, and professionally based services and to provide trusted and practical steel building solutions at competitive prices. Years of research and development, engineering input, computer programming and superior web design have allowed us to provide to you, the most innovative, unparalleled on-line design and pricing system in the world. Organizations large and small look to us for innovative solutions - we provide you with effective solutions to manage costs and promote customer satisfaction with every building. Within the industry, we stand alone in our innovation of design and engineering procedures and our ongoing commitment to customer service. The result? Affordability and an unprecedented ability to meet your specific needs.

Independence and Integrity: How We Conduct Our Business - What we do is important, but equally important is how we do it. From the beginning, we have taken the view that keeping up with our customer's demands requires objectivity, fairness, open processes, an attitude of respect, and adherence to best design and engineering practices. And, in part because we have always been independently owned, these core values remain at the center of our business ethic. In short, we believe integrity and excellence go hand in hand and our autonomy gives us the necessary freedom to put that belief into practice every day.

Knowledge and Innovation: Why We Excel: Year after year, we pursue a rigorous agenda of pertinent, unbiased research, probing the complexities of steel design. As an independent structural fabricator, we have no hidden agenda, no conflicts of interest, and no outside "dealer network" to protect. We objectively analyze patterns of our competitor's sales tactics, and routinely adjust pricing based on current market values. We seek to understand the causes of rising costs. And, most importantly, we use what we learn as the springboard for innovation. Staying in the "technological" front enables us to develop practical, workable strategies that will assure our continued success.

Pricing Excellence: What True Customer Service Means to Us - We think our customers should derive a real benefit from our online "real time" pricing program. That's why we define great service as giving customers what they most need and want. Knowledge empowers we help customers better manage their own needs, make wiser choices and lower their costs. We understand the importance of convenience too, so we made this automated service available to you at your leisure, day in and day out. We make quoting a steel building easy through our on-line pricing system. Make no mistake about it; our system is light-years beyond anything on the market today. Building on customer input, we created a broad range of user-friendly Internet tools that deliver the unprecedented ability to self-manage the design, pricing and purchasing of a new steel building. These tools include online member areas, building-specific accessory information, lease and finance information, our proprietary password protected quote storage, and a customized secure purchase area with multiple deposit payment options including credit card, personal check, and finance options.

Quality Products: Why We Put Structural Integrity First - The reason is simple: Your safety is our highest priority. Nothing illustrates our fundamental commitment to structural integrity and quality building design more clearly than our own proprietary design system. For example, we never consider any design until it has been demonstrated on the strength of clear and convincing scientific evidence to be safe and structurally sound. While cost is an important consideration, we consider the price of a building only after its structural merit has been established. You can be sure that we build our structures around the most advanced engineering practices.

Special Order Buildings: How We Deliver Results - Quality planning planning that begins anew with each customer makes all the difference. Our design specialists know that each customer presents unique circumstances and challenges. So we customize each plan, taking into account all the variables considering the implications from every angle. We also help take the guesswork out of decision-making. Using customer-specific data, our building design team can model results based on past experience and current available options so customer decisions are always well informed. The result is a collaborative solution fine-tuned to address both the customer's need to manage costs and design considerations.