Recommended Installation Methods of Insulation

Roof insulation rolls are cut to lengths that will cover the distance from eave to eave, leaving a one-foot overhang on each side of the building.

1) Start at the end of the building and temporarily secure one end of the roll by attaching the insulation to the eave strut with double-faced tape.

2) Pull the insulation across the purlins with the vapor barrier toward the building interior. Double-faced tape attached to the opposite end of the insulation will keep tension on the roof roll while the metal panels are being attached over the insulation.

3) Install the next roll in the same manner, making sure the rolls are stretched tight, aligned properly and closely butted.

4) Fasten tabs using one of the methods described on the following page. Any rips or tears must be covered with matching facing tape to ensure a tight vapor seal.

5) Trim excess insulation flush to prevent it from acting as a wick and moving water into the building.

Pre Engineered Metal Building

A pre engineered metal building is the obvious choice for a church or other type of meeting place. You may have noticed these structures since they are quickly becoming the "standard" in constructions methods. When you are looking for a cost effective way to meet your building needs, you should certainly think about a steel building. A pre-engineered metal building takes the risk out of putting yourself and your organization into debt. It is easy to identify the advantages in a pre-engineered metal building.

You could delay development for years while you line up funding, but why? Some choose to rent space from other property owners in lieu of the responsibility of new construction. The problem with this situation is you only have access to your meeting place around someone else's schedule. After taking into account and dismissing these ideas, take some time to think about talking to a steel metal building manufacturer.

As property and construction capital become harder to obtain, new solutions become ever more imperative. A pre-engineered metal building may perhaps not be part of the dream you have held for your club, association or church, however that shouldn't stop you. Some of the greatest things come in unlikely packages and we sometimes miss out when we disregard them too quickly.

Steel Buildings Are Economical

A steel building is an economical choice and will save you money in construction costs. We make it easy for you to design the building that's just right for you. We have implemented years of steel building design and engineering experience into our system, and you can be confident in your design requirements without worries. The "design it yourself" concept was designed to reduce costs. When you design your own steel building, we use the information you submit online to detail your steel building, just as you designed it. You can design endless steel building combinations without anyone trying to sell you a thing or make a commission. Take all the time you need, making changes to your building configurations are a snap. And of course, we are here to help you, when and if you need it. You can speak to a customer service representative, designer, engineer or project administrator at your convenience. We have no commissioned sales personnel, just experienced steel building professionals waiting to serve you.

Recommended Installation Methods of Insulation

Roof insulation rolls are cut to lengths that will cover the distance from eave to eave, leaving a one-foot overhang on each side of the building.

1) Start at the end of the building and temporarily secure one end of the roll by attaching the insulation to the eave strut with double-faced tape.

2) Pull the insulation across the purlins with the vapor barrier toward the building interior. Double-faced tape attached to the opposite end of the insulation will keep tension on the roof roll while the metal panels are being attached over the insulation.

3) Install the next roll in the same manner, making sure the rolls are stretched tight, aligned properly and closely butted.

4) Fasten tabs using one of the methods described on the following page. Any rips or tears must be covered with matching facing tape to ensure a tight vapor seal.

5) Trim excess insulation flush to prevent it from acting as a wick and moving water into the building.

Before you Buy

Do you know the company you're doing business with? Is the supplier a member of the Better Business Bureau? Do they have a record of dealing honestly? Can they refer you to satisfied customers? Is the physical address to the company available? Can you visit them at their offices? Are they a real company with a history of quality manufacturing? Are they Active Members of the AISC (American Institute of Steel Construction) Do they post any affiliation with any steel building association? Do you know what you are paying for? Does the steel building contract give line-item prices? Will you receive comprehensive set of erection plans? Are you getting written 30-year paint and 25-year Galvalume Plus® warranties? Does the contract specify 26 gauge panels? Does their roof panels include a "purlin bearing" leg? Does the roof system have an Underwriters Laboratories Class 90 rating? Are you being supplied with premium fasteners with a lifetime red-rust warranty? Will your steel building have a sculptured trim package? Are all the clips welded to primary structural components? Are the framed openings factory located? Does the supplier have the ability to engineer a custom design? Will you receive an 80+ page fully illustrated erection manual? Does the supplier have an in-house customer service department? Does the supplier actually manufacture what they sell? Do they process and produce all their drawings in-house? Do they ask you to sign a contract and pay a deposit before you know the total cost?