Steel Buildings vs. Conventional Construction

A great advantage of pre-engineered buildings is that they can be relocated if required. Since your building is shipped to you with a complete set of instructions, detailed engineering drawings and a shipping list, you can erect you steel building without consulting a construction company. This also means that should you someday decide to relocate, you can take down your building and erect it elsewhere.

Adding partition walls in a steel building allows one building to be a meeting room, or office and storage facility and another to be a restaurant. Building with steel gives you the ultimate in design flexibility. You can either own one outright or purchase a steel building to rent to others. Your one time cost is regained sooner rather than later when you rent it as mini storage or public meeting space. Steel buildings can be designed with a almost unlimited amount of options.

If you have a need for a new building, don't make a decision until you have explored your options with a qualified steel building manufacturer. The Steel Building Network has reviewed a wide range of manufacturers, suppliers and building industry professionals, and we know that no matter what your intended use, there is steel building system to suit your needs. Getting I contact with the right company to get your questions answered is the first step in having your building needs met.

Base Condition

Every metal building has some type of base connection along the building perimeter, allowing the connection of sheeting. This "base condition" determines exactly how the panels connect to the foundation. To prevent water and pests from entering the building at the base, panels extend below the finished floor of the building. Online design and pricing systems allows users to choose from a number of different base options.

Standard Base Angle - Our system defaults to a standard base angle condition. This condition consists of a single angle member, attached to both the wall sheets and the slab. Please note that the standard base condition requires that the slab be formed with a 1½" sheet notch to allow the sheets to extend below the top of the slab.

Deluxe Trim - Deluxe base trim is another option for buildings with concrete slab foundations. Deluxe base trim combines base angle and trim into one piece, providing all the benefits of base trim and base angle. Deluxe base trim is only available in burnished slate color.

Base Girt - The base girt option is designed for buildings that sit on piers rather than a full slab. A base girt system does not rest on or attach to the foundation. The base girt attaches to clips on the columns about 6" above the foundation. The base girt provides a great connection for liner panel.

Base Channel - The Base channel is a "cee" shaped section that runs the perimeter of the building connected to the floor. It is most commonly used when a liner panel, or interior wall, is going to be installed. The "cee" section provides a pre-positioned connection point for inside panels. This approach requires a sheet notch in the slab (for an alternative, see the combination of base channel and base trim below).

Visible Condensation

To effectively control visible condensation, it is necessary to reduce the cold surface areas where condensation may occur. It is also important to minimize the air moisture content within a building through the use of properly designed ventilating systems.

Proper Ventilation of a Building

Proper ventilation in a building can be an effective measure for condensation control. The end use of the building must be the controlling ventilation design parameter, especially above drop ceiling areas. Ventilation system design should be done at the initial building design stage. Use of a design professional is strongly recommended to assure the best possible system.

CONDENSATION CAN BE MINIMIZED THROUGH CONSIDERATION OF CLIMATE, RELATIVE HUMIDITY AND THICKNESS OF INSULATION.

Steel Building Manufacturers

Finding a bona fide steel building manufacturer is sometimes difficult. Everywhere you look there seems to be someone selling a "factory clearance" or "cancelled order" buildings. Well 99% of it is a farce. There are too many brokers and re-sellers out there to count. What they want is your deposit. You can fight with them about the actual details later. They just want the deposit. Take advantage of all the resources available to you. Try locating the manufacturer to match your expectations. This may be slightly more time consuming, but well worth it when your new steel building is delivered exactly to your specifications.

Getting multiple bids for any kind of service is key. Ask several steel building manufacturers to quote your building and explain precisely by line item what your price includes. You can turn to the Internet to seek out steel building manufacturers, but be warned. You will encounter many wolves in sheep's clothing. Contact the Better Business Bureau, or other affiliations to ensure a company has a good track record. Form a list of qualified steel building manufacturers, do your research and you can gauge which manufacturers you prefer to deal with. Once your bids are returned to you, the selection process should be easy to complete. You can choose to follow up with the most qualified companies to purchase your metal building or to ask additional questions.