Ridge Vent

Ridge vents come completely assembled for ease of installation. Ridge vents supplied by Metal Building Depot are of a low profile design to provide gravity type ventilation. Because gravity ridge vents are designed to allow free airflow, some penetration of water during blowing rains is to be expected. Standard available finishes for the ridge vents are polar white and galvalume. Other colors may be available at an additional cost. Nominal ridge vent length is 10'-0". Ridge vents are available with 9" and 12" throats. Bird screens are provided as a standard. The ridge vents can be ordered as continuous or single units. Exterior parts are 26 gage painted or galvalume. Interior parts are all made of G90 galvanized steel. The substructure consists of 10 gage saddle straps with interior baffles of 24 gage steel. Lifter arms and damper slides are made of 18 gage steel. Manual operation is through activation of a pull bar which is attached internally to bell cranked type lifter arms connected to the damper with Teflon coated pins through the damper slides. Dampers are spring loaded to remain in the open position until the pull bar is operated and locked in the closed position. Dampers operate in a vertical manner. Each vent is opened by a pull chain that extends approximately 12" below the roof unless noted otherwise on the order documents. Other opening mechanisms are available at an additional cost upon special request. Ridge vents should not be placed closer than 5’-0" to the endwall steel line to allow room to properly flash the building. For example, a 90’-0" long building with ridge vents required the entire length should have no more than (8) units. The ridge vents are available with the following accessories:

Steel Building Packages

Steel building kits are shipped with all the required hardware to construct a solid structure. Forget about running around town looking for bolts or brackets with steel building packages. When investigating steel building packages, request information about the different options that are available from each steel building manufacturer. Panel material or galvalume colors can complement any building and help to exceed your expectations. You can begin with more standard steel building packages and adjust them suit your specific needs.

Working with veteran professionals is the best way to build your new steel building. Completing the steps that help you decide on different configurations for your pre-engineered building insures your ultimate satisfaction. Each part of the design process should be explained and offered for your approval. Steel building manufacturers should be acquainted with commonly asked questions and should be able to anticipate your concerns.

PUBLIC and CHURCH

Serving the building needs of America's churches, schools and local, state or federal government is a challenge. A church in Tennessee (above) employs a 60-foot clearspan structure with a specially designed hip-roof to accommodate a spacious open sanctuary. Wood and drywall were used to cover the massive steel beams that meet in the center and support the heavy, built-up roof system. Outside, the application of brick gives the feeling of strength and permanence.

Sheeting

All sheeting is 26-gauge "R" panel. Color sheeting has a galvanized substrate to prevent rust and corrosion. All our Galvalume roof sheeting is hot dipped with a zinc and Aluminum compound to give it the strength to stand up to the worst weather, and the durability to last for generations.

Steel Building Manufacturers

Finding a bona fide steel building manufacturer is sometimes difficult. Everywhere you look there seems to be someone selling a "factory clearance" or "cancelled order" buildings. Well 99% of it is a farce. There are too many brokers and re-sellers out there to count. What they want is your deposit. You can fight with them about the actual details later. They just want the deposit. Take advantage of all the resources available to you. Try locating the manufacturer to match your expectations. This may be slightly more time consuming, but well worth it when your new steel building is delivered exactly to your specifications.

Getting multiple bids for any kind of service is key. Ask several steel building manufacturers to quote your building and explain precisely by line item what your price includes. You can turn to the Internet to seek out steel building manufacturers, but be warned. You will encounter many wolves in sheep's clothing. Contact the Better Business Bureau, or other affiliations to ensure a company has a good track record. Form a list of qualified steel building manufacturers, do your research and you can gauge which manufacturers you prefer to deal with. Once your bids are returned to you, the selection process should be easy to complete. You can choose to follow up with the most qualified companies to purchase your metal building or to ask additional questions.