Roof Extensions and Overhangs

Extensions can improve the appearance of a building but will cost more. Roof extensions add "curb-appeal" to some buildings, but will take more time to complete the erection of the building because of the amount of extra covering trim. Extensions can also help a building merge in better in an environment of conventionally constructed buildings in commercial areas. An overhang offers you some protection from the rain and shade from the sun. These options can be important when you receive many visitors to your building, by offering shelter from the elements.

We offer two types of roof extensions: (1) Gable Extensions for endwalls (2) Eave Extensions for sidewalls. Using our system, you can easily and quickly design and price buildings with overhangs up to 5' on any or all of the walls. When in the Building Accessories section select Roof Extensions.

Condensation Control

The condensation process occurs when warmer moist air comes in contact with cold surfaces such as framing members, windows and other thermally conductive accessories, or the colder region within the insulation itself (if moisture has penetrated the vapor retarder). Warm air, having the ability to contain more moisture than cold air, loses that ability when it comes in contact with cooler surfaces or regions. When this happens, excessive moisture in the air is released in the form of condensation. If this moisture collects in the insulation, the insulating value is decreased.

In dealing with condensation, air may be considered to be a mixture of two gases-dry air and water vapor. One thousand cubic feet of air at 75°F can hold up to 1.4 pints of water. At 45°F, it can hold only 0.5 pints.

Relative Humidity is a percentage measurement of the amount of water vapor present in the air in relation to the amount it is capable of holding at that temperature. Therefore, 50% Relative Humidity would mean that the air is carrying only one-half of the total amount of moisture that it could be holding at that particular temperature. Cold outside air is usually much drier than warm inside air. Therefore, you can lower the Relative Humidity by bringing in outside air to mix with and dilute the moist inside air. At 100% Relative Humidity, the air is "saturated."

The temperature at which the air is saturated and can no longer hold additional moisture is called the dew point temperature. Whenever air temperature drops below its dew point, excess moisture will be released in the form of condensation. Condensation problems are most likely to occur in climates where temperatures frequently dip to 35°F or colder over an extended period of time.

Base Condition

Every metal building has some type of base connection along the building perimeter, allowing the connection of sheeting. This "base condition" determines exactly how the panels connect to the foundation. To prevent water and pests from entering the building at the base, panels extend below the finished floor of the building. Online design and pricing systems allows users to choose from a number of different base options.

Standard Base Angle - Our system defaults to a standard base angle condition. This condition consists of a single angle member, attached to both the wall sheets and the slab. Please note that the standard base condition requires that the slab be formed with a 1½" sheet notch to allow the sheets to extend below the top of the slab.

Deluxe Trim - Deluxe base trim is another option for buildings with concrete slab foundations. Deluxe base trim combines base angle and trim into one piece, providing all the benefits of base trim and base angle. Deluxe base trim is only available in burnished slate color.

Base Girt - The base girt option is designed for buildings that sit on piers rather than a full slab. A base girt system does not rest on or attach to the foundation. The base girt attaches to clips on the columns about 6" above the foundation. The base girt provides a great connection for liner panel.

Base Channel - The Base channel is a "cee" shaped section that runs the perimeter of the building connected to the floor. It is most commonly used when a liner panel, or interior wall, is going to be installed. The "cee" section provides a pre-positioned connection point for inside panels. This approach requires a sheet notch in the slab (for an alternative, see the combination of base channel and base trim below).

Ceiling & Wall Liners

29g low rib panel applied to the interior of the building providing a clean protective covering over insulation or girt/purlin cavity.

RECREATIONAL

Todays sports, conditioning and recreational centers represent a multi-billion dollar business which continues to grow each year. Attractive, ultra-modern facilities are springing up everywhere, offering a myriad of activities to meet the recreational demands of our society.

Immense clear span, low cost-per-square-foot, and low energy costs are vital to the successful construction and operation of recreational facilities. Whether your need is for a tennis, bowling or health club facility, computerized design and manufacturing help our design engineers create building systems that meet the precise demands of recreational facilities with an eye to architectural designs that fit into any surrounding. Our engineers have designed and manufactured buildings for sports courts, sports fields, game rooms, locker rooms, roller rinks, ice rinks, riding arenas, recreational centers and every other pastime you can imagine. The most important element in the design of all these facilities was combining practicality with efficiency, while providing for the customers' needs. Equestrian buildings provide excellent examples of how the flexibility of these custom designs allow for cost-effective solutions to those specific needs. Your dealer can value-engineer a dollar-saving building system that fits the bill, whether your needs include an arena, a barn or a complete riding facility. Available from one stall to one hundred, with a center row or in a shed-row design, our value-engineered horse barns give you maximum space with a functional layout designed to streamline your horse operations. Riding arenas are available fully-enclosed or as a roof-only structure. Clear span arenas are available up to 240 feet wide and in unlimited lengths. Our engineering department and your dealer can work with you to custom design a structure which maximizes your building site with attached barns, tack rooms, or hay storage areas.